Varen er på lager.
Varen er bestilt fra leverandør og leveringsdato er bekreftet.
Varen er bestilt fra leverandør, men leveringsdato er ikke bekreftet.
Varen må bestilles fra leverandør.
Varen befinner seg på fjernlager.
Varen er bestilt fra leverandør, men leveringsdato er ikke bekreftet.
Varene bestilles fra vår leverandørs lager.
Ubekreftet - Ta kontakt med kundesenter for nærmere informasjon.
EXT-DVI-2500HD Gefen Inc. EXT-DVI-2500HD Gefen Extender DVI DL Tx/Rx 4xFiberLC 1xTP Max 100-2000 m EDID HDCP
EXT-DVI-2500HD Gefen Inc. EXT-DVI-2500HD Gefen Extender DVI DL Tx/Rx 4xFiberLC 1xTP Max 100-2000 m EDID HDCP EXT-DVI-2500HD Gefen Inc. EXT-DVI-2500HD Gefen Extender DVI DL Tx/Rx 4xFiberLC 1xTP Max 100-2000 m EDID HDCP

Gefen Extender DVI DL Tx/Rx

4xFiberLC 1xTP Max 100-2000 m EDID HDCP

Produktinfo
Extend dual-link DVI up to 6,600 feet (2 km)
The DVI•2500HD uses 4 strand fiber optic cables to extend Dual Link DVI display up to 6,600 feet away from your source. Dual link DVI describes the use of all 24 pins of the DVI (Digital Visual Interface) connector to achieve super high resolutions. Featuring Virtual DDC, the DVI•2500HD can run without the use of a CAT5 cable.
 
How It Works
The DVI•2500HD Sender unit sits next to your computer. Cables supplied with the DVI•2500HD system connect the DVI source to the DVI•2500HD Sender unit. The DVI•2500HD Receiver unit sits next to your Dual Link DVI display and plugs into the DVI display's dual-link DVI port. An optional CAT-5 cable and multi-mode 4 strand LC fiber optic cable (4-strand) connects the sender and the receiver units to each other.
 
Note: 
Single-mode fiber extensions can travel as far as 2km (6600 feet) using virtual EDID.
Multi-mode fiber extensions can travel as far as 500m (1640 feet)using virtual EDID.
 
For Direct DDC (DDC2B) mode, an additional CAT5 cable extension of up to 330 feet (100 m) is required. (The CAT5 cable is used for direct DDC2B, Hotplug and DC power.) This limits overall extension to 330 feet and makes unit HDCP-compliant.
 
For Virtual DDC Mode, the DVI extension is permitted to reach a maximum distance of 6,600 feet (2 kilometers) as the distance will no longer be limited to the CAT-5e cable used in Direct DDC mode. This mode does not support HDCP DVI resolutions can be up to 1920x1200 (single-link) and 2560x1600 (dual-link).
 
Features:
Extends any dual link DVI compliant device up to 6,560 feet (2 km) from the computer
Uses a 4 strand multimode LC-LC fiber optic cable; 2-strand/1-strand (duplex) for single-link
Optionally use one CAT-5e cable for DDC and control signals
Supports HDTV resolutions such as 720p and 1080p
Supports up to 2560 x 1600 resolution at 60Hz refresh rate.
Supports DDWG standards for DVI compliant monitors
Supports Virtual DDC and DDC2B protocols
HDCP-Compliant in Direct DDC Mode
Specifications:
Maximum Pixel Clock: 2 x 165 MHz
DVI resolution: Up to 1920x1200 (single-link), 2560x1600 (dual-link).
Input Video Signal: 1.2 volts p-p
Input DDC Signal: 5 volts p-p (TTL)
DVI Connector: DVI-D (24 pin) female
Video Link Connector: LC x 4
DDC Link Connector: RJ-45 Shielded
Power Supply: 12V DC
Power Consumption: 36 watts (max) each power supply
Dimensions: 8.4" W x 1.1" H x 4.4" D
Shipping Weight: 8 lbs.
 
Package Includes:
(1) DVI•2500HD Sender
(1) DVI•2500HD Receiver
(2) 12V Power Supply
(1) 6ft DVI-DL Cable (M-M)
(1) User's Manual
Copyright © 2014 Leteng AS - All rights reserved Webshopen er levert av MultiCase Norge AS (3.14.10.6 )